Every car needs a brake, hence it is an essential component. Only an electrical gadget can stop or slow down a moving vehicle. Every car has two distinct braking systems, one for each wheel. Modern, high-tech automobiles have an additional two-brake system, for a total of four. This page covers all you need to know about your car’s braking system. It also explains what to do if the braking system fails.

Braking Mechanisms

The four most common braking systems found in modern vehicles are discussed here;

Disc brakes: Most modern autos use a front disc braking system. It is made up of a braking rotor that is directly attached to the wheel.

Drum brakes were used on older autos and were situated near to the wheels. The vehicle’s braking system is housed in the rear axle and is connected to the inside of the wheel.

Independent emergency brakes are a feature of high-tech modern autos. They are used in emergencies and when parking an automobile. There are various types of emergency brakes. A push button, a stick lever between the driver and passenger, and so on could be employed.

ABS, or autonomous braking system, is a braking system found in modern, high-tech vehicles. If it detects a human or an automobile, it will promptly apply the brakes.

Factors Contributing to Vehicle Brake Failure

Brake pad failure is a common cause of vehicle braking failure. However, there are other common causes of braking system failure. They are:

Heat-Related Brake Pads

If you brake and drive aggressively, your brakes may become overheated. As a result, your brake pads get hard and the performance of your wheel rotor disc is lowered. In addition, incorrectly positioned brake pads may contribute to brake overheating.

Ownership error

This is a common reason for brake failure. Several manufacturers always guarantee the longevity of their brakes. This is limited to a standard driving style. In other words, how frequently a brake is utilized impacts how long it will last. Drivers must be aware of this and constantly remember to check their brakes.

Hydraulic Fluid Leak

The most common causes of hydraulic leakage are seal failure, temperature concerns, installation faults, hose failure, and pressure issues. Whether your car is having problems stopping, you should inspect it right once to discover if there is a hydraulic leak.

Driving in Wet or Soggy Conditions

If you were driving in muddy or rainy terrain, your brake pads and rotor discs would operate less efficiently. If you are driving through a wet area, lightly touch the brake pedal to remove any accumulated water. This would reduce friction between the brake pads and the rotor discs.

Pressure Drop in Hydraulic Brake Fluid

If the hydraulic brake fluid pressure disappeared, your car would be difficult to stop. If pressure declines, continually pump the brake pedals to recover pressure. This strategy, however, should only be utilized when absolutely essential. Otherwise, the brake pedals may experience more problems.

Overloaded cars and rotor disc damage

Overloading your car may reduce the efficiency of your brakes. They could damage the rotor discs, reducing the useful life of your brake pads.

Symptoms of a Car Brake Failure

It would be advantageous if you paid attention to the various indications sent by your vehicle and gave it a thorough inspection, especially when it comes to the brakes. Accidents will be prevented, as will a full shutdown.

Here are some signs of a Bad Brake:

The Brakes emit a foul odor.

If you notice a burning smell coming from your brakes, you should inspect them. The foul odor could be caused by burned brake pad components. In addition to being unhealthy, this causes unnecessary friction between the brake pads.

Shrill Sounds

Shrieks and howls indicate severe brake pad damage. In addition, the vehicle requires new brake pads. If they are not replaced, they may fail, affecting other braking components.

Audible Brake Warnings

Driving with your brake warning light on is strongly advised. The reasoning is that it would notify you if the brakes failed. If your brake light illuminates but your brake fluid levels are normal, continue driving to a repair facility for further inspection.

Unstable Brake Pedal

If you notice trembling in your brake pedal or steering wheel while driving, you should have your rotor discs checked. Furthermore, if there is oil, dirt, or another contaminated material in the automobile brake, your brake pedal may vibrate. As a result, it is preferable to develop the habit of cleaning your brakes on a regular basis.

Brake fade and fluid leaks

If you discover a fluid leak in the system, your car’s brakes may require repair. Another red flag is overheating, which can cause rapid brake fade while driving.

What Should I Do If My Car’s Brakes Fail While I’m Driving?

A car brake failure can be dangerous. However, if this occurs, take the following precautions to avoid mistakes or worse-case scenarios:

Try Not To Be Concerned

Even if it is difficult, try not to panic. Making a mistake out of fear could exacerbate the problem. You must remain calm, clear your mind, and look for a solution.

Turn on the warning lights

After regaining control, turn on your car’s warning lights. The warning light serves a defensive purpose. and would warn other drivers to keep clear of your vehicle. You can also honk continuously while running for cover.

Continue to depress the brake pedal.

If your car’s brakes aren’t working, try pressing the pedal harder. In newer vehicles, ABS may aid in pumping the brakes faster than the driver. If your vehicle lacks ABS, you will have to manually pump the drum and disc brakes. If no one responds, you could easily drive to a parking spot.

Use the hand or parking brake.

Parking brakes, in addition to disc and drum brakes, are a different type of brake. It aids in parking if your vehicle’s brakes fail. However, if you used it gradually, it might be beneficial. This is due to the chance that increasing your speed would cause your automobile to spin out and create a terrible accident. 

Never turn off the engine before coming to a complete stop.

Make sure you don’t turn off the engine before coming to a complete stop. This would result in loss of power steering and engine braking. It may also cause a steering wheel lock.

Leave the road and make a help request.

After parking, cautiously exit the road. Keep the hazard lights turned on before exiting the vehicle. then make an assistance request or have it hauled away for repairs.

Conclusion

If you see any of the warning flags above, you should inspect your brakes and take the necessary action. To get to safety if your brakes unexpectedly fail while driving, follow the guidelines above. Yuma Honda can assist you with your auto maintenance needs. 

Posted in Uncategorized | No Comments »

Under the Civic moniker, the Japanese automaker Honda manufactures a sport small vehicle called the Civic Si Sedan. This vehicle is a sedan. It is a high-performance edition of the standard Civic Sedan, and it is well-known for its stylish design, quick handling, and powerful engine. Additionally, it comes standard with a manual transmission. This high-performance variant of the Civic Sedan uses the ordinary Civic Sedan as its base model. Since the 1980s, Honda has been producing the Civic Si Sedan, and even today, many who are interested in purchasing vehicles that perform exceptionally well believe it to be one of the greatest choices that are now available.

The powerful engine that comes standard in the Honda Civic Si Sedan is undoubtedly one of the most remarkable aspects of this automobile. The most recent model is propelled by a turbocharged four-cylinder engine that has a displacement of 1.5 liters, produces 205 horsepower, and 192 pound-feet of torque. Because it has a six-speed manual transmission, driving this vehicle is a far more exhilarating and athletic experience than driving a vehicle with an automatic transmission. The highest speed that the vehicle is capable of reaching is roughly 130 miles per hour, and it can accelerate from 0 to 60 miles per hour in approximately 6.5 seconds.

One of the many things that have contributed to the success of the Honda Civic Si Sedan is its sporty look, which is one of the reasons why it is so well-known. The outside of the car has been given an aggressive appearance while yet maintaining its aerodynamic qualities. It comes equipped with LED headlights, an aggressive front grille, and a rear spoiler. Because it is equipped with alloy wheels that have a diameter of 18 inches, the car has a more aggressive stance when it is driven on the road. Another component of this vehicle that helps to its responsiveness and rapid handling is a suspension that has been modified specifically for sport.

The Honda Civic Si Sedan comes equipped with a range of cutting-edge safety features, some of which include adaptive cruise control, lane departure warning, and frontal collision warning, to name just a few of the available options. These functions make the car less hazardous to operate, which is one factor that contributed to the high safety ratings that it was awarded.

There is just one model of the Honda Civic Si Sedan available, and it is outfitted with a large variety of different conveniences and comforts as standard equipment. A Bluetooth connection, a music system with six speakers, and an infotainment system with a seven-inch touchscreen are some of the amenities that are included in this package. Additionally, the car is outfitted with an assortment of cutting-edge technical capabilities as standard equipment, such as compatibility with Apple CarPlay and Android Auto. Because of these features, connecting your smartphone to the multimedia system of the car is a straightforward process.

For the Honda Civic Si Sedan, consumers may choose from an extensive palette of color choices. These include classic tones such as Platinum White Pearl and Crystal Black Pearl, as well as daring colours such as Rallye Red and Tonic Yellow Pearl. Other examples are Crystal Black Pearl and Platinum White Pearl.

When it comes to its overall appearance, the Honda Civic Si Sedan has a look that can be described as both smart and aggressive. This is due to the car’s imposing front grille as well as its sleek body lines. Because the car is positioned at a low height in relation to the ground, it exudes a more dominant presence when traveling along the road.

Additionally, a great degree of customization possibility was included into the Civic Si Sedan throughout its development. Because there is such a large range of aftermarket components and add-ons available for purchase, you have the potential to modify your vehicle in such a way that it reflects your own, distinctive sense of style. Among these modifications are performance exhaust systems, cold air intake systems, and enhanced suspensions, to name just a few examples.

The Honda Civic Si Sedan distinguishes itself as one of the most forward-thinking automobiles available on the market today when it is fitted with the helical limited-slip differential that is an available option. This differential improves the car’s grip and stability during aggressive cornering as well as the car’s overall handling. In addition to that, the car has a suspension system that is tailored for performance, and it is standard equipment. This system has springs that are more firm, stabilizer bars that are thicker, and dampers that can adjust to changing conditions, all of which contribute to handling that is more responsive and agile.

In the inside of the Civic Si Sedan, you’ll find a leather-wrapped steering wheel, an elegant instrument cluster, and athletic seats that are both comfortable and sporty. In addition, the Civic Si Sedan comes standard with all-wheel drive. The car is also built with a variety of practical features such as an automatic climate control system, push-button ignition, and a sunroof, all of which combine to make the vehicle more joyful and relaxed to operate behind the wheel.

The EPA estimates that the Civic Si Sedan gets a highway fuel economy of 31 miles per gallon and a city fuel economy of 22 miles per gallon, which is very amazing for a sporty compact car like the Civic Si Sedan.

Overall, the Honda Civic Si Sedan is a sport compact car that gives a superb combination of sporty design, powerful performance, and advanced safety systems. You may have it as either a hatchback with five doors or a sedan with four doors. Because of its powerful engine, sport-tuned suspension, and highly changeable design, the Honda Civic Si Sedan is a fantastic choice for anybody looking for a vehicle that is both sporty and practical. This is because the car’s design allows for a great deal of personalization. It is a good choice for those who drive their vehicles on a daily basis due to the fact that it has improved fuel economy, innovative safety features, and innovative technology.

Conclusion

To provide a brief overview, the Honda Civic Si Sedan is a high-performance compact car that has an aggressive outer design, powerful internal powertrains, and cutting-edge safety systems. In other words, it is the perfect blend of these three elements. Because of its powerful engine, sport-tuned suspension, and highly changeable design, the Honda Civic Si Sedan is a fantastic choice for anybody looking for a vehicle that is both sporty and practical. This is because the car’s design allows for a great deal of personalization. The vehicle’s cutting-edge technological features, excellent fuel efficiency, and the helical limited-slip differential that can be purchased as an option make it an even more appealing choice for everyday drivers as well as enthusiasts of high-performance driving. In addition, the vehicle comes with a helical limited-slip differential that can be purchased as an option. The Honda Civic Si Sedan is still a popular choice among car enthusiasts because it is the perfect example of a vehicle that manages to effectively blend powerful performance, stylish design, and practicality. Visit us at Yuma Honda for more information on our cars and services!

Posted in Uncategorized | No Comments »

A car’s gearbox is a sophisticated system that is responsible for transferring power from the vehicle’s engine to the wheels that are used for propulsion. Because it enables the vehicle to drive and change gears at the appropriate times, it is a key component of an automobile. There are a few distinct types of transmissions, the most common of which being manual, automatic, and continuously variable transmissions (CVTs).

The driver of a vehicle equipped with a manual gearbox must physically change gears by using a clutch and a gear lever in order to operate the transmission. It is made up of a number of gears that are clustered together in a succession of groups that are referred to as gearsets. A number of shafts are used to transport power from the engine to the drive wheels. These shafts are linked to the gears by a series of shafts. By depressing the clutch pedal and then using the gear lever to engage the chosen gear, the driver is able to choose the gear they wish to utilize.

A manual gearbox normally consists of a number of gears, one of which is a reverse gear, which enables the vehicle to travel in the opposite direction of forward motion. It also features a neutral gear, which disengages the gearbox from the drive wheels so that the vehicle may be started and stopped without moving. This makes it possible to start and stop the vehicle without it actually moving. The clutch pedal in a manual gearbox is used to engage and disengage the transmission from the engine. A manual transmission also has a clutch pedal. Because it enables the driver to transfer gears in a smooth manner without bringing the engine to a complete stop, the clutch is a crucial component of a manual gearbox.

When driving a vehicle equipped with an automatic gearbox, on the other hand, the driver is not required to manually change gears. It utilizes a hydraulic system to carry out the task of automatically selecting the right gear for the vehicle depending on the speed and load of the vehicle. A torque converter, a set of gears, and a hydraulic system are the three components that make up an automatic gearbox. Both the car’s speed and its torque may be altered by shifting through the gears, which are controlled by the torque converter that is responsible for transferring power from the engine to the gearbox. The hydraulic system is responsible for controlling the flow of pressurized oil, which is then used for engaging and disengaging the gears according to the requirements of the situation.

Automatic transmissions often include a number of gears, one of which is a reverse gear that enables the vehicle to travel in the opposite direction of forward motion. Additionally, it features a park position that may lock the gearbox so that the vehicle cannot move while it is in that position. Because the hydraulic system automatically engages and disengages the gearbox from the engine, an automatic transmission does not have a clutch pedal. Instead, the transmission is connected to and disconnected from the engine.

Continuously variable transmissions, sometimes known as CVTs, are a kind of automatic gearbox that do not use set gear ratios. Instead, it adjusts the transmission ratio between the engine and the drive wheels by the use of a belt or chain, which allows for continual adjustment. This enables the automobile to attain a diverse range of ratios, which in turn enables it to achieve optimal performance while minimizing its impact on the environment. Two pulleys, a belt or chain, plus a hydraulic system make up a continuously variable transmission, often known as a CVT. Pulleys are used to transfer power from the engine to the drive wheels. These pulleys may be linked to one another by a chain or belt. The transmission ratio is determined by the tension that is placed on the belt or chain, and this tension is controlled by the hydraulic system.

In most cases, a continuously variable transmission will not have any set ratios or a reverse gear. Instead, it makes use of the same belt or chain to change the direction of the transmission ratio, which enables the vehicle to drive in the opposite direction as the forward movement. Because the hydraulic system automatically engages and disengages the gearbox from the engine, a continuously variable transmission, or CVT, does not have a clutch pedal.

Conclusion

To summarize, the gearbox is an essential component of a vehicle since it is in charge of transferring power from the engine to the driving wheels. Either a manual gearbox, in which the gears are changed by the driver themselves, or an automatic transmission, in which the gears are changed by the vehicle itself, are both viable options. There is also a third kind of gearbox known as a continuously variable transmission (CVT), which utilizes a belt or chain to continually alter the transmission ratio. This type of transmission may be found in certain vehicles. A gearbox is a vital component of an automobile since it enables the vehicle to move and change gears as required. The kind of transmission that is utilized does not matter. Visit us at Yuma Honda for more car information and any service you may need.

Posted in Uncategorized | No Comments »

Consumers have been able to purchase the pickup truck manufactured by Honda and branded as the Ridgeline from the year 2005. It is characterized by its one-of-a-kind unibody design, which combines the benefits of a traditional pickup truck with the ease and mobility of an SUV. This is what makes it stand out from other vehicles on the market today.

The Honda Ridgeline has gone through a number of redesigns and changes during the course of its production, each of which has brought about the addition of new capabilities and features. In this article, we are going to take a more in-depth look at the several Honda Ridgeline models and the primary qualities that are offered by each one.

First Generation (2005-2014)

The first generation of the Honda Ridgeline was introduced to the public in 2005, and it was powered by a V6 engine that dispensed 3.5 liters of displacement. It was available for purchase in a variety of various trim levels, including the RT, RTS, RTL, and RTL-T, and it came with a variety of distinct features.

One of the most prominent features of the original Honda Ridgeline was its unusual unibody structure, which stood out as one of the model’s most notable traits. Driving this car was notably more refined and pleasurable than driving a standard pickup truck. This is because it was designed on a basis that was akin to that of an SUV. In addition to this, it came pre-fitted with a wealth of cutting-edge safety features, such as traction control, stability control, and a host of other similar options.

The Generation that came after (2017-2021)

The second generation of the Ridgeline was introduced by Honda in 2017, and it differed significantly from the model that had been produced in the previous generation in a variety of key ways, including in terms of the alterations and additions. It had a V6 engine with a displacement of 3.5 liters and was available in a variety of various trim levels, such as the RT, Sport, RTL, RTL-T, and Black Edition versions. Additionally, it had a manual transmission.

One of the most significant enhancements made to the Honda Ridgeline in its second generation was the vehicle’s increased capacity to reduce its use of fuel. The vehicle received a variety of aerodynamic changes in addition to having an engine that was improved to be more fuel efficient. Both of these upgrades contributed to the decrease in the amount of gasoline that was needed to operate the vehicle. In addition, it was available with a variety of cutting-edge informational and safety technology, such as a touchscreen display, navigation, and adaptive cruise control, amongst others. These features were all included as optional extras.

Third Generation (2022-Present)

The third generation of the Ridgeline was introduced by Honda in 2022. When compared to the previous generation, this model included a substantial amount of updates and modifications that were designed to improve its overall performance. It has a V6 engine that is 3.5 liters in capacity and comes in a variety of various trim levels, some of which are the Black Edition, the RT, the Sport, the RTL, and the RTL-T. The Black Edition comes standard with a V6 engine that is 3.5 liters in capacity.

One of the most distinguishing features of this pick-up truck is the cutting-edge preventative safety technology that was included into the third generation of the Honda Ridgeline. All of the car’s cutting-edge driver assistance technologies, including as automatic emergency braking, adaptive cruise control, and lane departure warning, are included as standard equipment. The vehicle also boasts a number of other cutting-edge driver assistance technologies. It also has a more refined and modern exterior design, with a shape that is more aerodynamic and lines that are more forceful than its predecessor.

The Honda Ridgeline is often the option of drivers looking for a pickup truck that combines the attributes of a traditional truck with the comfort and handling of an SUV. In general, these drivers choose the Honda Ridgeline as their vehicle of choice a lot of the time. The Honda Ridgeline is a model that is continuously improving over time and getting more capable as newer generations are released. This is due to the fact that the Ridgeline has had new features and capabilities added to it with each new generation. 

Conclusion

If you are in the market for a pickup truck, whether it be for business or for recreational purposes, you should give some thought to acquiring a Honda Ridgeline. Visit us at Yuma Honda in order to learn more about Honda cars that are perfect for you.

Posted in Uncategorized | No Comments »

When purchasing a used car, there are a number of factors to take into account. You must first think about your budget, who you’ll be buying from, and the benefits that come with it. Following that, you must think about the type of automobile you desire. Contrary to new cars, you might not be able to acquire the precise model right away. Instead, you could find one that is comparable to or even better.

Regardless, purchasing a CPO vehicle is your best option. The used automobiles for sale that meet the requirements of manufacturer CPO programs are often checked for quality. In addition to this, the CPO program offers you a broad range of inventories to choose from.

Here is a used car checklist to help you if you’ve located the vehicle you wish to purchase;

The Vehicle’s History

Here is yet another crucial factor to take into account while looking for a used automobile for sale. Additionally, it’s crucial when purchasing a non-certified pre-owned vehicle. Because the car belonged to someone before it was placed up for sale, this is the case. And that individual may be a thief, a criminal, or a runaway.

Ask the vendor several safety-related questions before making a purchase. Run the vehicle identification number through a paid service, whether it came from the previous owner or a car dealership. You may learn more about the automobile from this.

Problems with the framework

The fundamental supporting framework of a vehicle to which all components are linked is called the chassis, sometimes referred to as the car frame. The main purpose of a chassis is to support both static and heavy loads without experiencing excessive distortion or deflection. Additionally, it supports the car’s body and mechanical components.

When buying a used automobile, pay close attention to the frame. Make that the automobile is straight and unharmed, and that nothing has been bent or damaged. Check the rest of the automobile to determine whether other components fit properly. If they don’t, bring it up to the seller’s notice.

Examine for Paint Damage or Rust

You should inspect the car carefully and look for any damage or fractures in the paint. And it’s not that difficult. By repainting the impacted area, you can repair the painted-over elements. Additionally, you may paint the entire automobile in the color of your choice.

Do not, however, disregard a rusted-out automobile. This is due to the danger that rusty cars might provide if they are disregarded. Speak up and ask the seller to rectify the issue, even if it’s just a tiny damage in one of the car’s components. Additionally, before paying for the car, you might want to reconsider your choice if you see that the majority of the places are corroded.

Each Tire’s Condition

When looking to purchase a used Honda vehicle, it is very important to look at the condition of the tires. To prevent a car collision or damage to another area of the vehicle, this is important. Verify the right wear pattern and alignment of all four tires.

The legal safety standard in the United States stipulates that a tire’s tread must be at least 2/32″ “deep. If the 2/32 is not met, “You might need to replace it if it is not up to par or even close to it. If you discover that the entire tire has to be replaced, carefully choose the appropriate size for the automobile.

If All of the Electronics are Functioning Correctly

Most people immediately think of the music system when they hear the word “automotive electronics.” However, it goes beyond that. Electronic controllers, safety airbags, headlights, brake lights, and other automotive electronics are also necessary. These electronics are broken down into many areas, including entertainment systems, driving aid, passenger comfort, and electronics for the gearbox and chassis.

The transmission system is managed by the transmission electronics. It facilitates effortless gear changes and communicates data between the transmission control and ECU. The anti-lock brake system, parking assistance, etc. are all part of the chassis electronics.

The entertainment systems category includes radio, navigation, and audio components. While blind-spot recognition is part of the driving assistance, the automated cooling system is controlled by passenger comfort.

Going For a Test Drive and What to Do in It.

The most important step in purchasing a secondhand automobile is this one. Don’t just assume that since everything looks good, it must be operating well. Take the vehicle for a test drive and pay special attention to how it behaves, sounds, and feels. Test the brakes, steering, suspension, acceleration, and other systems. Test it under various situations and at various speeds. Going with the vendor is advised so you can have a witness. Stop the purchase and look at another car if you find an issue that can’t be rectified simply.

Conclusion

Keep in mind that the moment you leave the dealership in a used automobile, the issues that the vehicle may have become your responsibility. Therefore, think everything over thoroughly and do your homework before proceeding. Do yourself a favour and use this checklist to your advantage, you will not regret it. If you want to get Honda cars from a certified Honda dealership, visit us at Yuma Honda. Here you can buy a great used Honda, or many other car brands, which are certified and in great state.

Posted in Uncategorized | No Comments »

As technology improves, a lot of things change, including automobiles. And this progression has led to the several differences between cars made in the past years and modern cars. . Modern-day cars possess a lot of technological features, artificial intelligent systems, and newer electrical components. One of the electrical components of a car is the sensor. 

A car sensor is an intelligent electronic device that observes and monitors a car’s surroundings and signals to the Electronic control unit(ECU) or the driver. In most cases, the ECU acts upon the signal and adjusts if the driver doesn’t take proper action. A car sensor can process information for controlling the engine, coolant system, oil pressure, vehicle’s speed, level of emission, e.t.c. Igniting your vehicle activates its sensor and monitors all aspects of the vehicle till it is brought to a halt. 

Types Of Car Sensors and Their Functions

Sensors are everywhere in Modern cars, from the major electrical components to the minor. This article explains the crucial types of car sensors and their functions. Below are the various kinds of sensors, their location, and respective functions; 

Air-flow Sensor

An air-flow sensor is a type of sensor that measures the density and volume of air flowing into the engine. And is located in the combustion chamber. This sensor ensures that the fuel mixture flows into the combustion chamber properly. And aids in effective performance. A failed air-flow sensor can cause a miscalculation of injected fuel, resulting in engine damage. 

Engine Knock Sensor

Engine knock happens when the mixture of air-fuel ignites before the spark is produced from the plugs. The engine knock sensor monitors the air-fuel mixture ignition process. It then alerts the driver if it detects any fault in the air-fuel mixture ignition. It’s strongly advisable to replace a bad knock sensor, as it can cost unimaginable damage to your engine. 

Engine Speed Sensor

The engine speed sensor is one of the critical auto sensor and is located in the crankshaft. It monitors the position and speed of the crankshaft and delivers the information to the electronic control unit(ECU). Also, the ECU gets the message, calculates the correct fuel injection time, and activates the spark plugs. This is imporant because failure to inject the fuel at the right time would make the engine lose its capability. 

Camshaft Position Sensor

This type of sensor collects data on the vehicle’s camshaft speed and relays data to the engine control module. It monitors the camshaft’s timing so that there is adequate air entry into the cylinder for burnt gasses to be sent out of it. Otherwise, It might damage the cylinder and power output.

Manifold Absolute Pressure (MAP) Sensor

The MAP sensor monitors the engine. It operates with the intake air pressure to process sufficient air and fuel quantities needed for the ignition cylinders. It calculates the difference between the manifold and outside pressure and ensures that the engine ingests fuel based on the change in pressure. A faulty MAP sensor will harm the engine’s air-fuel ratio, resulting in higher fuel consumption. 

Throttle Position Sensor(TPS) 

A throttle position sensor is a type of sensor used to monitor an engine’s air intake. It is located on the butterfly shaft, as it will help direct the position of the throttle. The sensor relays information to the ECU. And the ECU then calculates the amount of air-fuel mixture required for the cylinder. When a throttle position sensor gets damaged, it causes an engine shutdown.

Voltage Sensor

Voltage sensors are wireless tools used to monitor and calculate the vehicle’s idling speed voltage. It ensures that the vehicle’s idling speed is reduced or increased when needed. 

Oxygen Sensor

Oxygen sensor cars are effective. The Oxygen sensor, also known as O2, measures the unburned gasses present in the exhaust. The oxygen sensor in automobile is near the exhaust manifold after the catalytic converter. It can affect your engine’s timing, combustion intervals, and vehicle idling speed if it gets faulty. 

NO Sensor

This is another crucial sensor in the car. It monitors the amount of nitrogen oxide emitted from the vehicle while following strict laws. The sensor will then send a signal to the electronic control unit, which prepares the air-fuel mixture to attain the right amount of NO levels. 

Temperature Sensor

It’s a sensor that monitors the temperature of the engine and the consistent functioning of the car cooling system. It alerts the driver if the radiator isn’t working. And is located behind the front bumper and, sometimes, in the door mirror behind the glass. 

Fuel Temperature Sensor 

It’s a sensor that consistently monitors the fuel temperature. And then ensures that fuel is ingested into the cylinder at an optimal temperature for the efficient running of the engine. It’s located in the engine’s fuel rail, next to the air intake pipe. 

Speed Sensor

The speed sensor, just as it sounds, monitors and tracks the speed of each vehicle wheel. The information is relayed to the ECU. And the ECU works with safety features like traction control and an anti-lock braking system(ABS) for its utilization. 

Parking Sensor

The parking sensor works with the autonomous braking system(ABS). For instance, the sensor observes the vehicle’s environment and detects any obstacle(vehicle/pedestrian) in the front or back of the vehicle. It then alerts the autonomous braking system, which sends a beeping sound signal to the driver. If the driver hesitates to apply the brakes, the ABS does this instantly. 

Rain Sensor

The rain sensor is a safety device located on the windscreen. This sensor detects rain on the windscreen and alerts the electronic control unit(ECU). The ECU then activates the wipers if the vehicle has an automatic wiper function. 

Conclusion

These are the different types of sensors and their functions in the car. However, only some modern advanced cars possess all the sensors. At Yuma Honda, we sell an extensive collection of Honda cars with various sensors. Look through our inventory for your preferred car with sensor. And schedule an appointment with us today.

Posted in Uncategorized | No Comments »

Your car’s brakes are your first defense line against traffic fatalities. However, even the best car brakes have limited durability. Over time, brakes wear out and stop working if you do not prioritize dealing with them. This situation is called brake failure, and it is pretty frightening and dangerous. 

Brake failure can be very sudden and deadly. Nobody wants to imagine their car not stopping, especially when driving at freeway speeds. Fortunately, brake failure is rare today because modern vehicles have extensive features that guarantee the occupants’ safety. However, there are always exceptions. This article will expose you to the likely causes of brake failure, signs that your brakes might fail, and how to survive a brake failure in these rare exceptions. Read ahead! 

The Common Causes of Brake Failure 

Brake failure is pretty deadly as it leads to several death cases yearly. The following are the seven major causes of brake failure:

Owner’s Negligence 

Negligence is the most common cause of brake failure. Like many other automobile parts, brakes have a limited lifespan and should be regularly examined for wear. The lifespan of your brake shoes and pads will reduce if you constantly stop and go in cities. Although many brake shoes and pad brands boast high durability, the estimate is based on typical driving conditions. 

Damaged Rotor Disks 

Damaged rotor disks on your wheel can reduce the lifespan of your brake pads, causing stopping difficulty. When your brake pads are replaced, ensure to have your rotor disks smoothed by a professional mechanic. 

Overheating Brake Pads 

The car brake pads overheat due to excessive use. When this happens, they become brittle or stiff. The hardening reduces the ability of brake pads to grip the wheel rotor disk properly, thus increasing braking distance. 

Driving Through Mud or Water 

Drive cautiously in wet conditions when your wheels are submerged in water. The reason is that when you drive through water or mud, the required friction in the brake pads and rotor disks will reduce. Try tapping the brakes mildly to remove excess water and re-establish the friction between the rotor disks and brake pads. 

Leaking Hydraulic Fluid 

Oil and other hydraulic fluid can leak from your engine or brake lines. When you notice that stopping is difficult, examine your brakes to eliminate contaminants from a leaking hydraulic line. 

Loss of Hydraulic Brake Fluid Pressure 

This condition will reduce your ability to stop quickly. If you perceive that your brakes are not working or are working modestly, tap your brakes severally to force fluid throughout the brake system. Although this technique stops your car, you should not use it unless necessary. 

Vehicle Overloading

Load your car as recommended by the owner’s manual. Otherwise, it will affect its ability to stop and can lead to brake system failure. 

Signs of a Brake Failure 

When you begin to notice the following signs, you should get to safety and go for a car brake service as soon as possible:

• An increase in braking distance hints that your brakes may be struggling, making it longer to stop the vehicle. 
• If your brake pads feel unusual, like jumpy or mushy, there is a problem. 
• Unusual sounds like grinding noises from your brakes are signs of brake malfunction. 
• Sometimes, your brakes can fail without any warning and give no response when you press the brake pedal. This situation is an obvious sign of car brake problems. 

What to Do When Your Brakes Fail 

Having observed the causes and signs of brake failure. Let’s move on to what you should do when your car’s brake fails:

Stay Calm 

Staying calm when your vehicle suddenly refuses to come to a stop is easier said than done. Nonetheless, it would be best if you avoided panicking, which will cause you to make erratic movements, swerve, and make dangerous decisions. 

Remove Your Foot from the Gas 

When pressing the brake, you’ve probably removed your foot from the gas pedal. However, you might start pressing any pedal your legs can touch when you are in a panic. Taking your foot off the gas pedal can help you slow down. 

Attract Attention to Yourself

Turn on hazard lights and honk to warn other drivers that you are having a problem. You might also choose to flash your lights. They may not respond but will get out of your way. 

Feel for Objects Under Your Brake Pedal

Sometimes, brake failures can occur because of objects under the brake pedal. Put your foot under the pedal and kick out any object under there. Objects like cups and bottles can get behind the brake pedal, making it impossible to depress it. 

Don’t Turn off the Vehicle 

Only turn off the ignition once your vehicle has stopped entirely. If you turn it off, you might lose the ability to steer while moving. 

Don’t Go into Reverse or Park

You will only waste time going into reverse or park as it will not help and may be impossible. It might even cause you to lose control of your car. 

Drive up a Hill

Drive to a hill or any upward slope to slow your car down. Moreover, you must be careful of  the hill so you won’t roll back down. 

Apply Steady Pressure to the Brake Pedal

If you have anti-lock brakes, you can get them working by activating the anti-lock braking system (ABS). It will pump the brakes and build pressure to get them working. ABS brakes do not lock up, so you must give them firm, steady pressure. 

Use Your Engine Brakes 

Shifting into a lower gear can slow the vehicle when driving a manual. Press the clutch and slowly shift into the lower gears; the engine will slow the vehicle down. If you drive an automatic, move from D to 3, 2, and 1 to limit the gear and slow the car down. 

Carefully Apply the Emergency Brakes

The emergency brake can stop the car in an emergency. It is best to use it when your car has slowed down because when used at high speeds, it can cause your car to spin or skid off the road. Press the brake release button when applying the emergency brake so you can quickly release it if the brakes lock up. 

Conclusion

Brake failure is one of the primary causes of traffic fatalities. But thankfully, such fatalities have reduced in recent years due to extensive safety features fitted into modern cars. Nonetheless, car brakes not working correctly can be salvaged if you follow the life-saving tips mentioned above. 

You should check your brake system constantly for wear to ensure safe driving. If you want to order brake pads replacement and other car parts, you can visit our website at Yuma Honda. We provide quality car parts, efficient car servicing, and affordable used and new cars.  

Posted in Uncategorized | No Comments »

Key Takeaways:

1. If the engine belt is loose, your car will make a screeching noise.
2. Rattling car noises are often caused by something loose in the engine. It could be caused by a heat shield or a damaged piston.
3. A power steering fluid leak is a critical issue and should be fixed as soon as possible by a qualified mechanic.
4. Yuma Honda has factory-trained and experienced technicians, so they know how to get the job done quickly and correctly

Have you ever been driving along & suddenly; your car makes a noise that sounds like it’s coming from the depths of hell? It can be really spooky, especially if you don’t know what it means.

But don’t worry; we’re here to help you figure out what those spooky car noises mean & whether or not you should worry about these noises.

1. Screeching Noise When Starting the Engine

If your car is making a screeching noise when you start the engine, it could be a sign that your engine’s belt is either loose or damaged. The belt helps to drive the accessories in your engine, like the alternator, water pump, and power steering pump.

If the belt is loose, it can slip and cause many problems. If it’s damaged, it can break and leave you stranded. 

2. Hissing Noise Due to Leaks

Several things can cause a hissing car noise, but the most common culprit is a leak in the cooling system. This could be a radiator hose that has sprung a leak or a problem with the water pump. If you hear this noise, it’s critical to get your car to a mechanic as soon as possible so they can fix the leak and top off the coolant. 

3. Rattling Noise When The Car Is Idle

If your car rattles when idling, it could be a sign that your engine is misfiring. The engine misfires when the air/fuel mixture in the cylinders is ignited unevenly. This can happen for many reasons, like a dirty air filter or spark plugs. If the problem is intense, it can cause damage to your catalytic converter.

Rattling car noises are often caused by something loose in the engine. It could also be caused by a heat shield or a damaged piston.

4. Clunking Noise When Shifting Gears 

A few different things could be causing a clunking noise when you shift gears. Low transmission fluid or a loose engine mount can cause these car noises. It could be due to a damaged gearbox or worn-out bearings. If the problem is with your transmission, you’ll likely need to have it serviced by a professional mechanic. 

However, if the problem is with your engine mounts or bearings, you may be able to fix it yourself. In either case, it’s important to diagnose the problem as soon as possible to prevent further damage.

Related: How car service makes your car perform better? 

5. Clicking Noise When Turning 

The clicking noise when turning is due to a problem with your CV joints. The CV joints are located at the end of the axles and allow the wheels to turn while the suspension is moving up and down. If they’re damaged, you may hear a clicking noise when you turn the steering wheel. In some cases, the CV joints may also cause the wheels to feel loose. If you think your CV joints are the problem, it’s best to take them to a professional mechanic to have them checked out.

6. Grinding Noise When Braking 

A problem with brake pads or rotors may cause a grinding noise. The brake pads are responsible for providing friction to stop the wheels from turning, while the rotors are what the pads press against to create that friction. If either of these engine bay components is damaged or worn out, it can cause a grinding car noise when you brake. In some cases, the problem may be able to be fixed by simply replacing the brake pads. However, if the rotors are damaged, they will also need to be replaced.

7. Whistling Noise While Driving 

Your car’s belts may be the culprit behind the whistling car noise. The belts in your car are responsible for powering various components, such as the alternator, air conditioning compressor, and power steering pump. If one of these belts is loose, it can cause a whistling noise. You might be able to fix it by simply tightening or replacing the affected belt.

8. Rumbling Noise While Driving 

If you hear rumbling while driving, there are several possible causes. One possibility is that your car needs an oil change. When motor oil gets old, it can start to break down and form sludge. This sludge can build up in your engine and cause a rumbling noise. 

Exhaust leaks may cause it. Such leaks allow deadly carbon monoxide fumes to enter your car’s cabin. If you suspect an exhaust leak, get it fixed immediately by a qualified mechanic.

9. Squeaking Noise When Turning the Steering Wheel 

If you hear a squeaking sound emanating at the turn of a steering wheel, it’s most likely due to an issue with your power steering system. Power steering uses hydraulic fluid to make it easier to turn the steering wheel. If there’s a leak in the system, you’ll hear a squealing noise when you turn the steering wheel. You may notice that it’s hard to turn the steering wheel than usual. A power steering fluid leak is serious and should be fixed as soon as possible by a qualified mechanic.

10. Clicking Noise When Turning the Steering Wheel 

The clicking car noise when you turn the steering wheel, it’s most likely due to a problem with your CV joint. The CV joint allows the wheels to turn while the car is moving. If there’s damage to the CV joint, you’ll hear a clicking noise when you turn the steering wheel. 

A lack of lubrication can cause this damage, so make sure to have your mechanic check the CV joint and add lubrication if necessary.

11. Squeaking Noise When Turning the Steering Wheel 

If you hear squeaking when you turn the steering wheel, it might be due to a loose belt. The belts in your car engine are used to drive various components, such as the alternator, water pump, and power steering. If one of these belts is loose, it will squeal when the engine is running. You should have a professional mechanic tighten or replace the belt as soon as possible.

Read: 10 car sounds you should never ignore! 

Conclusion

If your Honda is making any of these spooky noises, don’t ignore it! These could be serious problems that will only worsen the longer you wait. Take your car to a nearby dealership or a professional mechanic to have it checked out and repaired if necessary.

You’re driving a Honda, so you’re doing something right. But even the best of us needs a little help from time to time. That’s why we offer auto service at our Yuma Honda, serving Yuma, AZ, dealership.

We want to keep your car operating like new for as long as possible, and that means proper maintenance is key. Bring it into our auto service center & let us take care of everything – from oil changes to major repairs.

Our professional mechanics are factory trained and very experienced, so they know how to get the job done quickly and correctly. Plus, we only use OEM parts and accessories in our repairs, so you can be sure your car will stay in top condition for years to come.

Schedule an appointment with us today! We’ll get you back on the road in no time.

Posted in Uncategorized | No Comments »

Key Takeaways:

• Current auto market trends are very favorable towards used car buyers & sellers.
• Regular auto maintenance, be it DIY or at a local dealership, can save you much in the long run & enhance your car’s value on resale.
• Certain practices & auto mods are essential in enhancing & maintaining your car’s value.
• Always consult an auto technician before you make any significant auto mods to enhance the value of your car for resale – not all mods are beneficial.
• Never alter or conceal the vehicle history details, as it can negatively impact your car’s resale value.

There is an insane list of things to keep in mind while maintaining your car’s value for later resale or trade-in plans. Regardless of a car’s value zeroing out after a decade of use, your car can still sell out at a reasonable price if you have been dedicated to a car care routine. Oh, you think we’re baiting you? Let’s back up the benefits of a car sale with the current auto market trends.

Car Ownership Trends Are Evolving.

People are leaning towards car leasing & used car buying more than considering outright auto financing.

71{0000de51c6c4c2cbc9e2e5b1f82e1b6f6ef093a955a2578688e5a3ee1cb0c22d} of auto buyers focus on car prices as the trigger point for more consideration regarding a car sale – new car prices are a deterrent.

Online car buying is an increasing norm across North American & European nations concerning used car sales because people in the middle-income strata find it affordable, trustworthy, & convenient.

Nearly 48{0000de51c6c4c2cbc9e2e5b1f82e1b6f6ef093a955a2578688e5a3ee1cb0c22d} of car owners reported lapsing their car maintenance routines because of the pandemic. Still, an astounding 49{0000de51c6c4c2cbc9e2e5b1f82e1b6f6ef093a955a2578688e5a3ee1cb0c22d} are already into auto maintenance to preserve their car’s value.

Nearly 69{0000de51c6c4c2cbc9e2e5b1f82e1b6f6ef093a955a2578688e5a3ee1cb0c22d} of Americans reported in 2019 that they would opt for a used car for their next car purchase – in 2022, used car sales have topped 43 million, nearly 3 times more than new car sales!

How Do You Benefit From This Information?

If you are an existing car owner and want to sell your car to invest in a newer or different model, the market trends are in your favor. The catch is that you must be a dedicated player in maintaining your car’s value for resale. 

If you are regular with your car care routine, all is well. If you have lapsed a bit, a mix of DIY & professional auto servicing will spruce up your car for sale in as little time as possible.

But there are things you must avoid doing to your car if you want your car to reap a worthy value on resale.

Also, read: 5 Reasons You Should Prefer a Dealership’s Auto Shop!

Maintaining Your Car’s Value – The 7 Don’ts Of Auto Value Care

1. Don’t Cheap Out On Maintenance

Wash & wax your car to the extent that you can see your reflection on the trunk. If you think a cheap wash & wax shampoo will cut it DIY – you’re in for many expenses for body paint restoration. Auto services might look expensive, but it takes only two professional wax coats to last a year. That’s better than repetitive DIY car wax disasters that will cost you longer.

2. Don’t Ignore Vehicle Aesthetics

Avoid using those telemarketer magic scratch erasers, DIY enamel, or resin to fill out deeper scratches that have cut through the paint. Let a body shop PDR the heck out of them. You can work on polishing the alloy wheels, rims, and plastic car trims, buffing the headlights & tail lights. Ensure the car’s exterior is decent for its age. Aesthetics are crucial to a used car sale markup.

3. Don’t Forgo Regular Deep Clean

Car interiors can become a hotbed for germs if not cleaned out thoroughly. If you want your car to rank high on resale in the future, you better start budgeting for a wet & dry vacuum service at your local dealership once every couple of months. That way, you get fresh & fragrant interiors.

If you want to do some cleaning yourself, you can invest in a car vacuum for the interiors. Or you can pop the hood and wash the engine bay. We have a DIY guide laid out just for you!

4. Don’t Misplace Auto Documentation

If you want to avoid awkward questions during the sale, you better document all of your car’s history. Yes, Carfax does record your car’s servicing history. Still, suppose you want a more accurate record of how well you have been maintaining your car’s value. In that case, you keep all your service receipts, MOT, auto logs & maintenance documents in one place.

5. Don’t Trust Private Hagglers

It’s good practice to have an auto mechanic regularly sound your car so you know it is performing optimally. Now, sometimes private buyers might try to undermine the rightful vehicle markup and offer you a lesser sum than the car is worth. Trust your research and avoid getting into haggling.

6. Don’t Smoke In The Vehicle

Nicotine & smoke deposits do take their toll on the interior of a car. You might not notice it until you do – the upholstery is coated in strange yellow grime that’s easy to remove. It’s the smell you won’t be able to get rid of. 

Buyers, even authorized local dealerships, will knock off a couple of hundred dollars for a clean car that smells like a cigarette factory. Even the HVAC is affected by the cigarette smoke deposits.

7. Don’t Lie On The Forms

If you have all your car documents and bodywork history, and your car suffered an accident that required reworking – don’t conceal that fact. Carfax reports indicating accident/collision history can affect resale prices. Still, it’s better to come clean about it rather than leave it to capable auto technicians to catch you lying on the forms. That can lead to sale cancelation altogether.

How To Enhance The Resale Markup On Your Car?

Not all auto mods add value to a car or enhance its value. So, if you need to boost the resale value of your car with aftermarket accessories or changes, these are the safest approaches:

• Invest in an infotainment system with a GPS. Preferably Apple CarPlay compatible.
• Switch out the old tires with weather-specific types or opt for an eco-range.
• Switching the old terry for leather upholstery with interior lighting is a valuable mod.
• Electric or power window upgrades or motorized side-view mirrors are ideal upgrades.
• Add a dashcam with a GPS mount, which might make your buyer’s day.

You might hear about how adding a body kit can enhance a car’s value. Still, the truth is that it suits certain cars, usually the sports or performance categories. 

Consult with our auto technicians & mechanics before you proceed with such a major modification. The same is advised for engine performance modifications.

Also, read: Are Modified Automobiles Worth the Money?

Sell or Trade-In?

If that question bothers you, the simplest way to resolve it is to find the utility in both options with respect to maintaining your car’s value. In a resale, you can sell to a private buyer, an individual, a friend, or an authorized local dealership. Only one of these is going to benefit you in a secure sale with minimal haggling, and you already know which one it is.

In a trade-in, you might be duped by a private buyer. Still, an authorized dealership will recognize your car’s value and help you put it up as a down payment for a new car or a lease, or it might be good enough for a switch!

Need Car Service? Need To Trade In A Car? You’re Welcome Here!

Yuma Honda, serving Yuma, AZ, deals in an outstanding range of new Honda, used vehicles, and breath-taking CPOs. We also have a fully-loaded auto center with trained auto technicians. We also cater to bad-debt financing for aspiring car owners. If you have a date with a car resale, we can help spruce your ride up for an impression that rakes in thousands. And, we’ll take your car in for a profitable trade-in if you visit us for a consult!

Get in touch with us or schedule a service; we’d be happy to help you get the most out of your car resale!

Posted in Uncategorized | No Comments »

Key Takeaways:

• Radiator fluids are important to prevent engine overheating. 
• Antifreeze is added to water to create a coolant solution that will lower the freezing point of the water and raise the boiling point.
• There are two different types of coolant: traditional & extended-life.
• It’s important to follow proper procedures when adding coolant to prevent damage. 
• Lack of coolant checkups results in severe engine issues & seizures.

There are all sorts of radiator fluids out there – knowing a little bit about radiator fluid can favorably extend the life of your car and keep it running smoothly. So, what exactly is radiator fluid, and what does it do? Radiator fluid, also called coolant or antifreeze, is a liquid that helps remove heat from your engine. 

As your engine runs, it produces a lot of heat. NADA Guides state that you cannot run a car for more than five minutes without coolant. The radiator fluids circulate through the engine, absorbing the heat and then carrying it away to the radiator, where it’s cooled down. This process keeps your engine from overheating, which can lead to serious damage.

Now let’s talk about the two main terms we hear about radiator fluids: antifreeze and coolant. Although they are used interchangeably, there’s a difference between the two!

Now let’s talk about the two main terms that we hear when we talk about radiator fluids: antifreeze and coolant. Although they are used interchangeably, there’s a difference between the two! 

The Difference Between Antifreeze and Coolant

Antifreeze is a substance that helps to prevent engine overheating by regulating the flow of coolant. It’s an ethylene-glycol solution that prevents freezing (as the name ANTIFREEZE suggests). 

Coolant is a 50/50 mixture of antifreeze & distilled water. It’s a fluid that helps to transfer heat away from engine parts. 

While antifreeze is necessary for preventing engine overheating, coolant is necessary for keeping the engine at a consistent temperature. 

This mixture of antifreeze & water (called coolant) provides the best protection against overheating and freezing. However, it’s important to consult your vehicle’s owner manual before adding any fluids to your engine because the wrong mixture can do more harm than good.

What Are the Different Types of Coolant? 

There are two main types of coolant: traditional green coolant and extended-life coolant. 

• Traditional green coolant is typically a mix of ethylene glycol and water.
• Extended-life coolants use propylene glycol and include corrosion inhibitors. 

Extended-life coolants can last up to five years or 150,000 miles without needing to be replaced. Traditional coolants must be replaced every two years or 30,000 miles.

If you’re unsure which coolant to use, check your vehicle’s owner’s manual or ask a qualified mechanic.

What Do Different Colors of Coolant Identify?

Different coolant colors identify the chemical makeup of the coolant and how they should be used. The different colors can help you choose the right coolant for your car. 

• Blue coolant is typically used in European cars.

• Red coolant is typically used in Asian cars.

• Green coolant is used in American cars.

What Are Some Tips for Properly Adding Coolant?

When adding coolant, it’s important to follow the proper procedure to avoid damaging your engine. 

• First, make sure the engine is cool before opening the radiator cap. If the engine is hot, wait until it cools down before continuing. 
• Once the engine has cooled down sufficiently, remove the radiator cap & slowly add the coolant to the radiator.
• Be careful not to overfill it; the coolant should only come up to the level of the radiator opening. 
• Once you’ve added the coolant, replace the radiator cap and start the engine. Let it throttle for a few minutes, then check the level again and add more coolant if necessary.

What Are Some of The Dangers of Not Keeping Your Antifreeze or Coolant Levels Up to Par, And How Can You Avoid Them Altogether?

Did you know that if your car overheats just once, it can cause irreversible damage to the engine? Not to mention, it can also cause the radiator and hoses to crack. And we all know how expensive car repairs can be. The best way to avoid all this is to simply keep an eye on your antifreeze or coolant levels and top them off when necessary. It’s a small price to pay for peace of mind and a healthy car.

1. Your Engine Could Freeze Up

If your antifreeze or coolant levels are low, your engine could freeze and resist ignition. This is particularly dangerous in cold weather, as a frozen coolant in engine & radiator hoses generate internal stresses that can damage the engine block. Not only will this leave you stranded, but with a cracked engine that will need to be replaced!

To avoid this, check your antifreeze or coolant levels regularly and top them up if necessary.

2. Your Car Could Overheat

When your antifreeze or coolant levels are low, your car could overheat. This is especially dangerous in hot weather, as an overheated engine is at risk of seizure. 

To avoid this, make sure to keep an eye on your temperature gauge and pull over if it starts to climb too high.

3. You Could End Up with a Cracked Engine Block

You could also end up with a cracked engine block if you are careless about your coolant levels. This is because when the coolant freezes, it expands and puts pressure on the engine block. Over time, this can cause the engine block to crack!  

To avoid this, keep your antifreeze or coolant levels topped up year-round, especially in the winter. 

FAQs About Antifreeze and Coolant – Answered!

1. How Often Should You Replace Your Antifreeze/Coolant?

Most carmakers recommend changing your coolant every 30,000 miles or every two years, whichever comes first. Extended-life coolant has a lifespan of 150,000 miles, but most traditional coolants last for a maximum span of five years. 

2. What Are the Signs to Replace Your Coolant?

You can usually tell when it’s time to replace your antifreeze/coolant with its color. If it’s cloudy or rusty, it’s time for a change. 

You should also be on the lookout for leaks. A small leak might not seem like a big deal, but it can quickly lead to engine damage if left unchecked. So, if you’re due for a coolant change or suspect your coolant is leaking, take your car to a mechanic & have them check it out. 

3. How Much Will It Cost You to Change Coolant?

The cost to change coolant depends on a few factors, such as the type of antifreeze and the amount you need. Generally, you must pay between $50 and $200 for a typical antifreeze change. 

Conclusion

Antifreeze/Coolant prevents your engine from overheating in summer and freezing in winter by lowering the freezing point of the water and raising the boiling point. It is important to keep your coolant fresh and at the correct level and to keep an eye out for leaks. 

Yuma Honda, serving Yuma, AZ, has the best car service center in Arizona. There are many benefits of dealership service centers over independent repair shops. If unaware of these benefits, come to our dealership and see for yourself! 

Whether you need radiator fluid change, coolant flush service, or full repair – we have expert mechanics to assess your situation and provide the best solution! 

Book your service appointment now!

Posted in Uncategorized | No Comments »